A bit of a non-traditional fall color palette for this fall card, but I like it! I used the Leaf Fall Embossing folder on the background and tied in a combo of stamp leaves and leaves die cut from the All About Autumn Designer Series Paper pack.

Measurements

Full list of supplies needed, listed below. A die cutting machine is needed for this card.
Blackberry Bliss Cardstock: 5 1/2″ w x 8 1/2″ h folded to 5 1/2″ w x 4 1/4″ h
Very Vanilla Cardstock:

• 5 1/4″ w x 4″ h (2)
• scrap for sentiment and leaf

All About Autumn Designer Series Paper (DSP): scrap for die cut leaves

Let’s Create

1. Affix all stamps to Acrylic Blocks.
2. Fold the Card Base in half using a Bone Folder to sharpen the crease.
3. Use a blending brush to apply some Moody Mauve to one of the Very Vanilla panels. Then run it through the Leaf Fall embossing folder.
4. On scrap Very Vanilla, stamp the large maple leaf in Blackberry Bliss and die cut.
5. Die cut two maple leaves and one oak leaf from the All About Autumn DSP.
6. Stamp the sentiments in Blackberry Bliss on Very Vanilla scrap and die cut out.
7. Arrange the leaves and sentiments on the embossed panel. Arrange Very Vanilla Baker’s Twine behind the Sentiments and attach all the pieces with Stampin’ Seal, Mini Glue Dots, and/or Stampin’ Dimensionals.
8. Sprinkle on the gems.
9. Stamp and decorate the remaining Very Vanilla panel for the inside and attach with Stampin’ Seal.
10. Decorate your envelope.
11. So pretty! Who will you send it to?

Product List

Recommended Stamper’s Toolkit ❤

 

Such a beautiful color combination on this card for a friend. Make this card or CASE (copy and share everything) the layout with supplies from your stash.

Measurements

Full list of supplies needed, listed below. A die cutting machine is needed for this card.

Basic White

• 5 ½” x 8 ½”  scored and folded on the long-side at 4 ¼” 
• 5 ¼” x 4”  
• 4” x 3” (for die cutting sprig)
• 2 3/4” x ¾” (for stamping and die cutting sentiment)

Pebbled Path

• 4 ⅛” x 5 ⅜”
• 5” x 2 ⅛”
• 3 ¾” x 1 ¾” 
• 4” x 4” (for die cutting 2 sets of leaves)

Masterfully Made Designer Series Paper

• 4 ⅞” x 2 (Lost Lagoon Leaf print)
• 3 ⅝” x 1 ⅝” (Piece taken from the center of the print with bold flowers)

Let’s Create

1. Affix all stamps to Acrylic Blocks.  
2. Fold the Card Base in half using a Bone Folder to sharpen the crease.
3. Using the Exposed Brick 3D Embossing Folder, emboss the 5 ¼” x 4” Basic White Cardstock.
4. Using a blending brush with the Pebbled Path Ink Pad, lightly brush ink on the rougher side of the cardstock. 
5. Using the smaller leaf sprig die from the Gorgeously Made die set, die cut 2 of the Leaf sprigs from the 4” x 4” Pebbled Path cardstock. 
6. Using the larger sprig from the Gorgeously Made die set, die cut 1 from the 4” x 3” Basic White cardstock. Using a blending brush lightly brush Lost Lagoon ink onto the sprig.
7. Using Pebbled Path ink pad, stamp the sentiment onto Basic White 2 ¾” x ¾” scrap. Die cut this piece using the label from the Gorgeously Made die set.
8. Assembling your card:  Attach the 5 ⅜” x 4 ⅛” Pebbled Path cardstock to the folded card base.  Attach the embossed 5 ¼” x 4” embossed Basic White to the card layers.
9. Attach the Designer Series Papers to their coordinating Pebbled Path layers.  
10. Tie a piece of textured Pebbled Path Ribbon around the layered piece of Designer Series Paper that measures 3 ⅝” x 1 ⅝” into a knot towards the left side.
11. Position these layers to the Basic White embossed panel about ¾” from the lower left edge.
12. Place adhesive on the back of the other Designer Series layered pane and slip it under the ribbon and adhere to the card.
13. I did a little trimming on the die cut sprigs so they weren’t quite so full and bulky and adhered them to the card. 
14. Adhere the sentiment using Stampin’ Dimensionals. 
15. Finish your card by randomly placing 3 Rhinestones Basic Jewels onto your card.
16. Be sure to decorate the inside of the card and the envelope.
17. Send it off to a special friend.

Shopping List

Recommended Stamper’s Toolkit ❤